User:Jhurley/sandbox

Advection and Groundwater Flow

Groundwater migrates from areas of higher hydraulic head (a measure of pressure and gravitational energy) toward lower hydraulic head, transporting dissolved solutes through the combined processes of advection and dispersion. Advection refers to the bulk movement of solutes carried by flowing groundwater. Dispersion refers to the spreading of the contaminant plume from highly concentrated areas to less concentrated areas. Dispersion coefficients are calculated as the sum of molecular diffusion, mechanical dispersion, and macrodispersion. In many groundwater transport models, solute transport is described by the advection-dispersion-reaction equation.

Related Article(s):

• Dispersion and Diffusion
• Sorption of Organic Contaminants
• Plume Response Modeling

CONTRIBUTOR(S):

• Dr. Charles Newell, P.E.
• Dr. Robert Borden, P.E.

Key Resource(s):

• Groundwater, Freeze and Cherry, 1979.
• Hydrogeologic Properties of Earth Materials and Principals of Groundwater Flow, Woessner and Poeter, 2020.

Groundwater Flow

Figure 1. Hydraulic gradient (typically described in units of m/m or ft/ft) is the difference in hydraulic head from Point A to Point B (ΔH) divided by the distance between them (ΔL). In unconfined aquifers, the hydraulic gradient can also be described as the slope of the water table (Adapted from course notes developed by Dr. R.J. Mitchell, Western Washington University).

Groundwater flows from areas of higher hydraulic head toward areas of lower hydraulic head (Figure 1). The rate of change (slope) of the hydraulic head is known as the hydraulic gradient. If groundwater is flowing and contains dissolved contaminants it can transport the contaminants from areas with high hydraulic head toward lower hydraulic head zones, or “downgradient”.

Darcy's Law

Table 1. Representative values of total porosity (n), effective porosity (n_e), and hydraulic conductivity (K) for different aquifer materials

Aquifer Material	Total Porosity (dimensionless)	Effective Porosity (dimensionless)	Hydraulic Conductivity (meters/second)
Unconsolidated
Gravel	0.25 — 0.44	0.13 — 0.44	3×10-4 — 3×10-2
Coarse Sand	0.31 — 0.46	0.18 — 0.43	9×10-7 — 6×10-3
Medium Sand	—	0.16 — 0.46	9×10-7 — 5×10-4
Fine Sand	0.25 — 0.53	0.01 — 0.46	2×10-7 — 2×10-4
Silt, Loess	0.35 — 0.50	0.01 — 0.39	1×10-9 — 2×10-5
Clay	0.40 — 0.70	0.01 — 0.18	1×10-11 — 4.7×10-9
Sedimentary and Crystalline Rocks
Karst and Reef Limestone	0.05 — 0.50	—	1×10-6 — 2×10-2
Limestone, Dolomite	0.00 — 0.20	0.01 — 0.24	1×10-9 — 6×10-6
Sandstone	0.05 — 0.30	0.10 — 0.30	3×10-10 — 6×10-6
Siltstone	—	0.21 — 0.41	1×10-11 — 1.4×10-8
Basalt	0.05 — 0.50	—	2×10-11 — 2×10-2
Fractured Crystalline Rock	0.00 — 0.10	—	8×10-9 — 3×10-4
Weathered Granite	0.34 — 0.57	—	3.3×10-6 — 5.2×10-5
Unfractured Crystalline Rock	0.00 — 0.05	—	3×10-14 — 2×10-10

In unconsolidated geologic settings (gravel, sand, silt, and clay) and highly fractured systems, the rate of groundwater movement can be expressed using Darcy’s Law. This law is a fundamental mathematical relationship in the groundwater field and can be expressed this way:

Where:

Q = Flow rate (Volume of groundwater flow per time, such as m³/yr)

A = Cross sectional area perpendicular to groundwater flow (length², such as m²)

V_D = “Darcy Velocity”; describes groundwater flow as the volume of flow through a unit of cross-sectional area (units of length per time, such as ft/yr)

K = Hydraulic Conductivity (sometimes called “permeability”) (length per time)

ΔH = Difference in hydraulic head between two lateral points (length)

ΔL = Distance between two lateral points (length)

Hydraulic conductivity (Table 1 and Figure 2) is a measure of how easily groundwater flows through a porous medium, or alternatively, how much energy it takes to force water through a porous medium. For example, fine sand has smaller pores with more frictional resistance to flow, and therefore lower hydraulic conductivity (Figure 2) compared to coarse sand, which has larger pores with less resistance to flow.

Figure 2. Hydraulic conductivity of selected rocks.

Darcy’s Law was first described by Henry Darcy (1856) in a report regarding a water supply system he designed for the city of Dijon, France. Based on his experiments, he concluded that the amount of water flowing through a closed tube of sand (dark grey box in Figure 3) depends on (a) the change in the hydraulic head between the inlet and outlet of the tube, and (b) the hydraulic conductivity of the sand in the tube. Groundwater flows rapidly in the case of higher pressure (ΔH) or more permeable materials such as gravel or coarse sand, but flows slowly when the pressure is lower or the material is less permeable, such as fine sand or silt.

Figure 3. Conceptual explanation of Darcy’s Law based on Darcy’s experiment (Adapted from course notes developed by Dr. R.J. Mitchell, Western Washington University).

Since Darcy’s time, Darcy’s Law has been adapted to calculate the actual velocity that the groundwater is moving in units such as meters traveled per year. This quantity is called “interstitial velocity” or “seepage velocity” and is calculated by dividing the Darcy Velocity (flow per unit area) by the actual open pore area where groundwater is flowing, the “effective porosity” (Table 1):

Where:

V_S = “interstitial velocity” or “seepage velocity” (units of length per time, such as m/sec)

V_D = “Darcy Velocity”; describes groundwater flow as the volume of flow per unit area (units of length per time)

n_e = Effective porosity (unitless)

Effective porosity is smaller than total porosity. The difference is that total porosity includes some dead-end pores that do not support groundwater. Typically values for total and effective porosity are shown in Table 1.

Figure 4. Difference between Darcy Velocity (also called Specific Discharge) and Seepage Velocity (also called Interstitial Velocity).

Darcy Velocity and Seepage Velocity

In groundwater calculations, Darcy Velocity and Seepage Velocity are used for different purposes. For any calculation where the actual flow rate in units of volume per time (such as liters per day or gallons per minute) is involved, then the original Darcy Equation should be used (calculate V_D; Equation 1) without using effective porosity. When calculating solute travel time, then the seepage velocity calculation (V_S; Equation 2) must be used and an estimate of effective porosity is required. Figure 4 illustrates the differences between Darcy Velocity and Seepage Velocity.

Mobile Porosity

Table 2. Mobile porosity estimates from 15 tracer tests

Aquifer Material	Mobile Porosity (volume fraction)
Poorly sorted sand and gravel	0.085
Poorly sorted sand and gravel	0.04 — 0.07
Poorly sorted sand and gravel	0.09
Fractured sandstone	0.001 — 0.007
Alluvial formation	0.102
Glacial outwash	0.145
Weathered mudstone regolith	0.07 — 0.10
Alluvial formation	0.07
Alluvial formation	0.07
Silty sand	0.05
Fractured sandstone	0.0008 — 0.001
Alluvium, sand and gravel	0.017
Alluvium, poorly sorted sand and gravel	0.003 — 0.017
Alluvium, sand and gravel	0.11 — 0.18
Siltstone, sandstone, mudstone	0.01 — 0.05

Payne et al. (2009) reported the results from multiple short-term tracer tests conducted to aid the design of amendment injection systems. In these tests, the dissolved solutes were observed to migrate more rapidly through the aquifer than could be explained with typically reported values of n_e. They concluded that the heterogeneity of unconsolidated formations results in a relatively small area of an aquifer cross section carrying most of the water, and therefore solutes migrate more rapidly than expected. Based on these results, they recommend that a quantity called “mobile porosity” should be used in place of n_e in equation 2 for calculating solute transport velocities. Based on 15 different tracer tests, typical values of mobile porosity range from 0.02 to 0.10 (Table 2).

A data mining analysis of 43 sites in California by Kulkarni et al. (2020) showed that on average 90% of the groundwater flow occurred in about 30% of cross sectional area perpendicular to groundwater flow. These data provided “moderate (but not confirmatory) support for the mobile porosity concept.”

Advection-Dispersion-Reaction Equation

The transport of dissolved solutes in groundwater is often simulated using the Advection-Dispersion-Reaction (ADR) equation. As shown below (Equation 3), the ADR equation describes the change in dissolved solute concentration (C) over time (t) where groundwater flow is oriented along the x direction.

Where:

R is the linear, equilibrium retardation factor (see Sorption of Organic Contaminants),

D_x, D_y, and D_z are hydrodynamic dispersion coefficients in the x, y and z directions (L²/T),

v is the advective transport or seepage velocity in the x direction (L/T), and

λ is an effective first order decay rate due to combined biotic and abiotic processes (1/T).

The term on the left side of the equation is the rate of mass change per unit volume. On the right side are terms representing the solute flux due to dispersion in the x, y, and z directions, the advective flux in the x direction, and the first order decay due to biotic and abiotic processes. Dispersion coefficients (D_x,y,z) are commonly estimated using the following relationships:

Where:

D_m is the molecular diffusion coefficient (L²/T), and

α_L, α_T, and α_V are the longitudinal, transverse and vertical dispersivities (L).

The ADR equation can be solved to find the spatial and temporal distribution of solutes using a variety of analytical and numerical approaches. The design tools BIOSCREEN, BIOCHLOR, and REMChlor employ an analytical solution of the ADR equation. MT3DMS uses a numerical method to solve the ADR equation using the head distribution generated by the groundwater flow model MODFLOW (McDonald and Harbaugh, 1988).

See Also

• International Water Management Institute Animations
• NAU Lecture Notes on Advective Transport
• MIT Open CourseWare Solute Transport: Advection with Dispersion Video
• Physical Groundwater Model Video
• Online Lecture Course - Groundwater Flow